JBL Bar 2.0 ALL-IN-ONE
Bar 2.0 ALL-IN-ONE
OWNER’S MANUAL
IMPORTANT SAFETY INSTRUCTIONS
Verify Line Voltage Before Use
The JBL Bar 2.0 (soundbar) has been designed for use with
100-240 volt, 50/60 Hz AC current. Connection to a line voltage
other than that for which your product is intended can create
a safety and fire hazard and may damage the unit. If you have
any questions about the voltage requirements for your specific
model or about the line voltage in your area, contact your retailer
or customer service representative before plugging the unit into
a wall outlet.
Do Not Use Extension Cords
To avoid safety hazards, use only the power cord supplied
with your unit. We do not recommend that extension cords be
used with this product. As with all electrical devices, do not run
power cords under rugs or carpets, or place heavy objects on
them. Damaged power cords should be replaced immediately
by an authorized service center with a cord that meets factory
specifications.
Handle the AC Power Cord Gently
When disconnecting the power cord from an AC outlet, always
pull the plug; never pull the cord. If you do not intend to use this
speaker for any considerable length of time, disconnect the plug
from the AC outlet.
Do Not Open the Cabinet
There are no user-serviceable components inside this product.
Opening the cabinet may present a shock hazard, and any
modification to the product will void your warranty. If water
accidentally falls inside the unit, disconnect it from the AC power
source immediately, and consult an authorized service center.
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS 2
1 INTRODUCTION 4
2 WHAT’S IN THE BOX 4
3 PRODUCT OVERVIEW 4
3.1 CONTROLS AND INDICATORS 4
3.2 CONNECTORS 5
3.3 REMOTE CONTROL 5
4 PLACE 6
4.1 DESKTOP PLACEMENT 6
4.2 WALL-MOUNTING 6
5 CONNECT 6
5.1 TV CONNECTION 6
5.2 BLUETOOTH CONNECTION 7
6 PLAY 7
6.1 POWER-ON/AUTO STANDBY/AUTO WAKEUP 7
6.2 PLAY FROM THE TV SOURCE 8
6.3 PLAY FROM THE BLUETOOTH SOURCE 8
7 SOUND SETTINGS 8
8 RESTORE FACTORY SETTINGS 9
9 SOFTWARE UPDATE 9
10 PRODUCT SPECIFICATIONS 9
11 TROUBLESHOOTING 9
12 TRADEMARKS 10
13 OPEN SOURCE LICENSE NOTICE 10
1 INTRODUCTION
Thank you for purchasing the JBL Bar 2.0 All-in-One (soundbar)
which is designed to bring an extraordinary sound experience to
your home entertainment system. We encourage you to take a
few minutes to read through this manual, which describes the
product and includes step-by-step instructions for setting up
and getting started.
To make the most of product features and support, you
may need to update the product software through the USB
connector in the future. Refer to the software update section
in this manual to ensure that your product has the latest
software.
Designs and specifications are subject to change without notice.
If you have any questions about the soundbar, installation or
operation, please contact your retailer or customer service
representative, or visit our website: www.jbl.com.
2 WHAT’S IN THE BOX
Unpack the box carefully and ensure that the following parts are
included. If any part is damaged or missing, do not use it and
contact your retailer or customer service representative.
3 PRODUCT OVERVIEW
3.1 Controls and indicators
Status indicators
3.2 Connectors
3.3 Remote Control
4 PLACE
4.1 Desktop placement
Place the soundbar on a flat and stable surface.
NOTES:
−− The power cord shall be properly connected to power.
−− Do not place any objects on the top of the soundbar
4.2 Wall-mounting
1. Preparation:
a) With a minimum distance of 2” (50mm) from your TV, stick
the supplied wall-mounting template to a wall by using
adhesive tapes.
b) Use your ballpen tip to mark the screw holder location.
Remove the template.
c) On the marked location, drill a 4 mm/0.16” hole. Refer to
Figure 1 for the screw size.
2. Install the wall-mounting bracket.
3. Fasten the screw onto the back of the soundbar.
4. Mount the soundbar
NOTES:
−− Make sure that the wall can support the weight of the soundbar.
−− Install on a vertical wall only.
−− Avoid a location under high temperature or humidity.
−− Before wall-mounting, make sure that cables can be properly
connected between the soundbar and external devices.
−− Before wall-mounting, make sure that the soundbar is unplugged from
power. Otherwise, it may cause an electric shock.
5 CONNECT
5.1 TV connection
Connect the soundbar with your TV through the supplied HDMI
cable or an optical cable (sold separately).
Through the supplied HDMI cable
An HDMI connection supports digital audio and video with a
single connection. HDMI connectivity is the best option for your
soundbar.
1. Connect the soundbar with your TV by using the supplied
HDMI cable.
2. On your TV, check that HDMI-CEC and HDMI ARC have been
enabled. Refer to the owner’s manual of your TV for more
information.
NOTES:
−− Full compatibility with all HDMI-CEC devices is not guaranteed.
−− Contact your TV manufacturer if you have problems with the HDMICEC
compatibility of your TV.
Through an optical cable
• Connect the soundbar with your TV by using an optical cable
(sold separately).
5.2 Bluetooth connection
Through Bluetooth, connect the soundbar with your Bluetooth
device, such as a smartphone, tablet and laptop.
To reconnect the last paired device
Your Bluetooth device is retained as a paired device when the
soundbar goes to standby mode. Next time you switch to the
Bluetooth source, the soundbar reconnects the last paired
device automatically.
To connect to another Bluetooth device
NOTES:
−− The Bluetooth connection will be lost if the distance between the
soundbar and Bluetooth device exceeds 33 ft (10 m).
−− Electronic devices may cause radio interference. Devices that generate
electromagnetic waves must be kept away from the soundbar, such
as microwaves and wireless LAN devices.
6 PLAY
6.1 Power-on/Auto standby/Auto wakeup
NOTES:
−− Use the supplied power cord only.
−− Before switching on the soundbar, make sure that you have completed
all other connections (See “TV connection” in the “Connect” chapter).
Auto standby
If the soundbar is inactive for more than 10 minutes, it will switch
to standby mode automatically. Next time you switch on the
soundbar, it returns to the last selected source.
Auto wakeup
In standby mode, the soundbar will wake up automatically when
• the soundbar is connected to your TV through the HDMI
ARC connection and your TV is switched on;
• the soundbar is connected to your TV through an optical
cable and audio signals are detected from the optical cable.
6.2 Play from the TV source
With the soundbar connected, you can enjoy TV audio from the
soundbar speakers.
NOTES:
−− If the soundbar is connected to your TV through both an HDMI cable
and an optical cable, the HDMI cable is selected for the TV connection.
6.2.1 TV remote control setup
To use your TV remote control for both your TV and the soundbar,
check that your TV supports HDMI-CEC. If your TV does not
support HDMI-CEC, follow the steps under “TV remote control
learning”.
HDMI-CEC
If your TV supports HDMI-CEC, enable the functions as instructed
in your TV user manual. You can control the volume +/-, mute/
unmute, and power on/standby functions on your soundbar
through the TV remote control.
TV remote control learning
6.3 Play from the Bluetooth source
Through Bluetooth, stream audio from your Bluetooth device to
the soundbar.
7 SOUND SETTINGS
Audio sync
With the audio sync function, you can synchronize audio and
video to make sure that no delay is heard from your video content.
1. On the remote control, press and hold TV.
→→ Ready for audio sync: The status indicator scrolls white.
2. Within five seconds, press + or - on the remote control to
adjust the audio delay and match with video.
→→ The status indicator scrolls to show the change range.
Smart mode
With the smart mode enabled by default, you can enjoy TV
programs with rich sound effects. For TV programs such as
news and weather forecasts, you can reduce sound effects by
disabling the smart mode and switching to the standard mode.
Smart mode: EQ settings and JBL Surround Sound are applied
for rich sound effects.
Standard mode: The preset EQ settings are applied for standard
sound effects.
To disable the smart mode, do the following:
• On the remote control, press and hold until the status
indicator scrolls white. Press +.
→→ When the smart mode is disabled, the status indicator
scrolls white twice.
→→ Next time you switch on the soundbar, the smart mode is
enabled again automatically.
8 RESTORE FACTORY SETTINGS
9 SOFTWARE UPDATE
For optimal product performance and your best user experience,
JBL may offer software updates for the soundbar system in the
future. Please visit www.jbl.com or contact JBL call center to
receive more information about downloading update files.
1. Check that you have saved the software update file to the root
directory of a USB storage device. Connect the USB device
to the soundbar.
2. To enter the software update mode, press and hold and - on
the soundbar for more than 10 seconds.
→→ When software updating is complete, you will hear a
confirmation tone.
→→ The soundbar returns to the last selected source.
NOTES:
−− Keep the soundbar powered on and the USB storage device mounted
before software updating is complete.
10 PRODUCT SPECIFICATIONS
General specification:
• Power supply: 100 - 240 VAC, ~ 50/60 Hz
• Total speaker power output (Max. @THD 1%): 80 W
• Soundbar output power (Max. @THD 1%): 2 x 40 W
• Soundbar transducer: 2 x racetrack drivers
• Soundbar standby power: <0.5 W
• Operating temperature: 0°C - 45 °C
Video specification:
• HDMI Video output (With Audio return channel): 1
Audio specification:
• Frequency response: 70 Hz - 20 KHz
• Audio inputs: 1 Optical, Bluetooth, USB (USB playback is
available in US version. For other versions, USB is for Service
only.)
USB specification (Audio playback is for US version only):
• USB port: Type A
• USB rating: 5 V DC / 0.5 A
• Supporting file format: mp3, wav
• MP3 Codec: MPEG 1 Layer 2/3, MPEG 2 Layer 3, MPEG
2.5 Layer 3
• MP3 sampling rate: 16 KHz - 48 KHz
• MP3 bitrate: 80 kbps - 320 kbps
• WAV sample rate: 16 KHz - 48 KHz
• WAV bitrate: Up to 3000 kbps
Wireless specification:
• Bluetooth version: 4.2
• Bluetooth profile: A2DP V1.3, A VRCP V1.5
• Bluetooth frequency range: 2402 MHz - 2480 MHz
• Bluetooth Max. transmitting power: <10 dbm (EIRP)
• Modulation type: GFSK, π/4 DQPSK, 8DPSK
Dimensions:
• Soundbar dimensions (W x H x D): 614 x 58 x 90 mm /
24.17” x 2.28” x 3.54”
• Soundbar weight: 1.61 kg
• Packaging dimensions (W x H x D): 855 x 125 x 145 mm
• Packaging weight (Gross weight): 2.6 kg
11 TROUBLESHOOTING
Never try to repair the product yourself. If you have problems using this product, check the following before you requiest services.
System
The unit will not turn on.
- Check if the power cord is plugged into power and the soundbar
The soundbar has no response to button pressing.
- Restore the soundbar to factory setting (See the "RESTORE FACTORY SETTING" chapter)
Sound
No sound from the soundbar
Distorted sound or echo
• If you play audio from your TV through the soundbar, make
sure that your TV is muted or the built-in TV speaker is
disabled.
Audio and video are not synchronized.
• Enable the audio sync function to synchronize audio and
video (See “Audio sync” in the “SOUND SETTINGS” chapter).
Bluetooth
A device cannot be connected with the soundbar.
• Check if you have enabled Bluetooth on the device.
• If the soundbar has been paired with another Bluetooth
device, reset Bluetooth (see “To connect to another device”
under “Bluetooth connection” in the “CONNECT” chapter).
• If your Bluetooth device has ever been paired with the
soundbar, reset Bluetooth on the soundbar, unpair the
soundbar on the Bluetooth device, and then, pair the
Bluetooth device with the soundbar again (see “To connect
to another device” under “Bluetooth connection” in the
“CONNECT” chapter).
Poor audio quality from a connected Bluetooth device
• The Bluetooth reception is poor. Move the source device
closer to the soundbar, or remove any obstacle between the
source device and the soundbar.
The connected Bluetooth device connects and disconnects
constantly.
• The Bluetooth reception is poor. Move the source device
closer to the soundbar, or remove any obstacle between the
source device and the soundbar.
• For some Bluetooth devices, the Bluetooth connection can
be deactivated automatically to save power. This does not
indicate any malfunction of the soundbar.
Remote control
The remote control does not work.
• Check if the batteries are drained. If so, replace them with
new ones.
• Reduce the distance and angle between the remote control
and the main unit.
12 TRADEMARKS
The Bluetooth® word mark and logos are registered trademarks
owned by the Bluetooth SIG, Inc. and any use of such marks by
HARMAN International Industries, Incorporated is under license.
Other trademarks and trade names are those of their respective
owners.
The terms HDMI, HDMI High-Definition Multimedia Interface, and
the HDMI Logo are trademarks or registered trademarks of HDMI
Licensing Administrator, Inc.
Manufactured under license from Dolby Laboratories. Dolby,
Dolby Audio and the double-D symbol are trademarks of Dolby
Laboratories.
13 OPEN SOURCE LICENSE NOTICE
This product contains open source software licensed under
GPL. For your convenience, the source code and relevant build
instruction are also available at http://www.jbl.com/opensource.html.
Please feel free to contact us at:
Harman Deutschland Gmb
HATT: Open Sour ce, Gregor Krapf-Gunther, Parkring 3
85748 Garching bei Munchen, Germany
or OpenSourceSupport@Harman.com if you have additional
question regarding the open source software in the product.
